Tjyylli

I want to write that command in a .bat file and run it by windows scheduler at certain times of night and morning.

(for example: open connection at 23:00 and close it again next day at 9:00 automatically)

Already I am doing same procedure with using netsh command (in below) that can disable/enable my "Local Area Connection" and cause Ethernet light of my modem to be turned off (that is one of 4 lights of modem including: Power, Ethernet, DSL, Internet)

netsh interface set interface name="Local Area Connection" admin=disabled/enabled

And now I want to find a way to close the connection to the ISP (which cause DSL and Internet lights of the modem to be turned off) or a way to disconnect it (which cause Internet light of the modem to be changed from Green to Red).

My modem: ZyXEL "P-650R-T1v3"

--

Update 1:
What about DSL connection and turning off its light or in other word closing connection to the ISP?

--

Update 2: In response to the good and detailed answer of MR. @Michael_Kjörling, I changed my question and now I think my ultimate goal as mentioned in update 1 is terminating/closing my connection to the ISP and vice versa.

(Option 2 of @Michael_Kjörling answer with a difference: I want to turn on the Internet connection during the night (from 23:00 to 09:00 o'clock of next day and also,) leave the computer on for a specific internet usage when I'm not in front of my PC to operate it manually and remember that I don't want to leave my pc with internet access before 23:00 and after 09:00)

When I use netsh command, it does not close my connection to the ISP and in connection log of my user in ISP website, I am still connected. But when I remove/unplug my telephone wire from modem or turn the modem off or using "Connect On-Demand" future of modem Web UI, then I can see the disconnection time in log page of ISP website and reach my goal physically! (However I want to reach my goal by command and scheduler or a similar way without using a timer because I don't want to pay for it if I can reach my goal without purchasing a Timer device.)

--

Update 3: What about Connect On-Demand ability?

It's not work fine for my goal.

And what about connect/disconnect Button in Web UI of Modem?

Is there anyway to handle that work by schedule? for example using a command that sends user-name and password of Web UI with a parameter to modem to tell it to be connected/disconnected.

Honestly, I think you are trying to over-engineer this. I can see two obvious options, depending on what is your ultimate goal.

1. You want to eliminate the light from the modem, because you find it distracting. In this case, just cover the lights with something, perhaps something as simple as a piece of cardboard. Make sure to not cover any ventilation holes.




2. You want to turn off the Internet connection during the night, but leave the computer on. This is exactly what a timer (or more accurately, an electric time switch) does. Hook your modem to it, set it to turn off the power between 23:00 and 09:00, and call it a day (or night). I'd suggest caution with the cheapest models as they might not play very nicely with sensitive electronics.

Virtually any other alternative is going to basically replicate the functionality of either one of those options, likely for more effort.

Simple time switches often are 24-hours only, but there exist those that can be set to take into account the day of the week (here is one example that allows for eight on/off cycles per day for seven days, which I was able to find with a quick Google search; your local home supply store will undoubtedly be able to suggest possibilities).

Additionally, taking your question at face value:

now I want to find a way to power off/on my modem totally.

If the modem is truly powered off, how is the computer going to be able to turn it on (which implies that there's something still powered on, else there would be nothing for the computer to communicate with)? That is essentially the same question as in is it possible to wake up a Linux device at a specific time (full disclosure: the accepted answer is mine), except in this case we have much less control over the device in question.

its rough but here is how I did it on windows 8

@echo off



rem get the name of the adapter to turn off

wmic nic get name



rem turn off adapter

wmic path win32_networkadapter where name="SOME ADAPTER THAT NEEDS TURNED OFF" call diable 2>nul



rem turn on adapter

wmic path win32_networkadapter where name="SOME ADAPTER THAT NEEDS TURNED OFF" call enable 2>nul



exit